center max distance 260 Swing on the cutting table 140 5000rpm M.T.No.1 electric motor 0.75kw

Bed swing 200mm center 200mm 1800,2250,2800,3400rpm(50Hz) MT No.1 Bed(length×width）500×80mm 0.4kw-2P

Center:450 Swing over bed:100 Swing over cross table:75

φ220*380 total length of the bed:850 Bed width:155 Swing over saddle:100

φ360*550 Cross swing:φ210 Spindle bore:φ40 85-1800rpm(6steps) Tail stock stroke-120mm MT-4

JN07 7 inch chuck Bed swing 360 Swing on the carriage 210 Center distance 550 Bed size length×width 1360×275 Spindle taper MT No.5 83-1800rpm output 2.2kw

φ360×500 Swing over cross table:180 No.5 Hole through:32 56-2500rpm Tailstock spindle movement:120 Bed length:1350 S:480×245×100 3.7kw×4P

7"3-jaw chuck (SOUL MS#7）

Max. work-piece diameter over bed: -Nominal: 630 mm -Max.: 660 mm Max. work-piece diameter over support: -At short slides: 400 mm -At long slides: 320 mm Max. work-piece diameter in a notch in front of a faceplate: 720 mm Length of a notch in front of a faceplate: 265 mm Height of centers: -Over bed: 305 mm -Over floor level: 1125 mm Bed width: 550 mm Working spindle bore: 72 mm Faceplate: -Diameter: 630 mm -Width: 120 mm Transversal section of the cutter: -Width: 40 mm -Height: 40 mm Side length of the tool holder: 200 mm Number of revs of the main electric motor: 1400 rpm Number of spindle speeds: 18 Max. allowable number of faceplate revs: 560 rpm Feeds: -Longitudinal feeds: -Number: 68 -Range: 0,035-10 mm/rev -Transversal feeds: -Number: 68 -Range: 0,014-4 mm/rev Speed of rapid stroke: -Longitudinally: 5000 mm/min -Transversely: 2000 mm/min Thread: -Step: -Number: 84 -Range: 0,2-224 mm -Inch: -Number: 94 -Range: 140-1/8 threads per inch -Module: -Number: 72 -Range: 0,1-112 -Pitch: -Number: 94 -Range: 280-1/4 Machine dimensions: -Length: 2300 (+ distance between centers) mm -Width: 1850 mm -Height: 1725 mm

JPY 180,000

7"3-jaw chuck (KITAGAWA JN07)

φ435*650 Distance from floor to spindle center:1075 Distance from bed to spindle center:215 Bed length:1680

Swing Over Bed........................ 12" Max Swing in Gap: .................... 17" Effective Length in Gap: ............. 5" Width of Bed: ........................ 7-1/4" Distance Between Centers.............. 36" Spindle Nose: ........................ D1-4 Spindle Hole.......................... 1-1/2" Spindle Drive......................... 1.5 HP Spindle Speeds........................(9) 70 - 1400 RPM Electrics.............................220v 1ph Control: 2 Axis Newell DP700 Digital Read Out Equipped With: Inch Metric Threading Digital Readout (Option) 5C Collet Closer (Option) 6" 3 Jaw Chuck 8" 4 Jaw Chuck 3-3/4" Steady Rest 10" Face Plate Tailstock Factory Tool Kit 4 Way Tool Post Thread Chasing Dial Center & Sleave Full Length Splash Guard

φ400*965 spare chuck

Swing Over Bed : 400 Swing over Cross Slide : 220 Center to Center : 800 Width : 310 Spindle Bore : 45mm

φ6"*900 1600 rpm